Qlogic HBA card in E450 with errors

I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot sequence, before the Openboot banner appears:
Unimplemented FCode token before address fff0dce9
Warning: Fcode sequence resulted in a net stack depth change of 1

Also the following messages appear during boot up:
WARNING: /pci@1f,4000/scsi@3 (glm0):
SCSI bus DATA IN phase parity error
Target 0 reducing sync. transfer rate
Target 0 disabled wide SCSI mode
Target 0 reverting to async. mode

Can you tell me whether I have a problem with the cable or the card or both? How do I troubleshoot this?

Thanks so much
Margaret

which SUNW packages do you mean? what kind of HBA is it? please give model and firmware version (qlogic or sun firmware...).

Solaris 9 SUNWsan,SUNWcfpl,SUNWcfplx packages were installed.
Patches 113046,113049,113039,113040,113041,113042,113043,113044 and 111847
The card is a qlogic QLA2342
The OPB version is
OBP 3.30.0 2003/11/11 10:41 POST 6.1.0 2003/11/11 10:27

maybe this card won't work in an rather old 450... if you boot up solaris, please post the output of:

# luxadm -e port
# luxadm qlgc
# cfgadm -al

I have attached the output in a zip file.

Not sure if the attachment made it, so here is the full output
luxadm -e port.....

Found path to 2 HBA ports

/devices/pci@6,2000/SUNW,qlc@1/fp@0,0:devctl NOT CONNECTED
/devices/pci@6,2000/SUNW,qlc@1,1/fp@0,0:devctl NOT CONNECTED

luxadm qlgc.....
Found Path to 2 FC100/P, ISP2200, ISP23xx Devices

Opening Device: /devices/pci@6,2000/SUNW,qlc@1/fp@0,0:devctl
Detected FCode Version: ISP2312 Host Adapter Driver: 1.14.09 03/08/04

Opening Device: /devices/pci@6,2000/SUNW,qlc@1,1/fp@0,0:devctl
Detected FCode Version: ISP2312 Host Adapter Driver: 1.14.09 03/08/04
Complete
cfgadm -al......
Ap_Id Type Receptacle Occupant Condition
c0 scsi-bus connected configured unknown
c0::dsk/c0t0d0 disk connected configured unknown
c0::dsk/c0t1d0 disk connected configured unknown
c1 scsi-bus connected configured unknown
c1::dsk/c1t6d0 CD-ROM connected configured unknown
c2 scsi-bus connected configured unknown
c2::dsk/c2t0d0 disk connected configured unknown
c2::dsk/c2t1d0 disk connected configured unknown
c2::dsk/c2t2d0 disk connected configured unknown
c2::dsk/c2t3d0 disk connected configured unknown
c3 scsi-bus connected configured unknown
c3::dsk/c3t0d0 disk connected configured unknown
c3::dsk/c3t1d0 disk connected configured unknown
c3::dsk/c3t2d0 disk connected configured unknown
c4 scsi-bus connected configured unknown
c4::dsk/c4t0d0 disk connected configured unknown
c4::dsk/c4t1d0 disk connected configured unknown
c4::dsk/c4t2d0 disk connected configured unknown
c4::dsk/c4t3d0 disk connected configured unknown
c5 scsi-bus connected configured unknown
c5::dsk/c5t0d0 disk connected configured unknown
c5::dsk/c5t1d0 disk connected configured unknown
c5::dsk/c5t2d0 disk connected configured unknown
c6 fc connected unconfigured unknown
c7 fc connected unconfigured unknown

from what i see, your hba's are fine. the errors looks like a faulty scsi device. so maybe one of your disks is bad...

OK, but what about the luxadm -e port?. It shows "NOT CONNECTED", and why is an orange light flashing to the right of the HBA card on the back of the server? I have a properly connected HBA card on anoher E450, and there are no flashing error lights and the luxadm -e port gives a value of "CONNECTED". Can you tell me exactly what the fcode errors mean? Thanks for your help on this so far

Margaret

Flashing light does not means its erred.
Pls install the SAN patches for Solaris 9:o

try the sansurfer also. normaly if luxadm does it witout probs that mean U are ground up. The amber light flashing before the OS boots is normal/