My wireless card: TP-LINK 322G +
I ask, after the installation is complete debian5.04, how to configure wireless Internet access, thank you!
lspci entry:
00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1)
00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2)
00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2)
00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2)
00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3)
00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1)
00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2)
00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2)
00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2)
00:08.1 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2)
00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2)
00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
I use a variety of methods,
For example: Download zd1211-firmware
Then I use the command: cp -R zd1211-firmware/* /lib/firmware/zd1211
I tried modprobe zd1211rw.
But no results
The results of my lsusb command is:
Bus 002 Device 003: ID 0e8d: 0002 MediaTek Inc.
Bus 002 Device 002: ID 046d: c018 Logitech, Inc. Optical Wheel Mouse
Bus 002 Device 001: ID 1d6b: 0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0ace: 1215 ZyDAS WLA-54L 802.11bg
Bus 001 Device 001: ID 1d6b: 0002 Linux Foundation 2.0 root hub
I use the ifconfig command, the result is:
lo Link encap: Local Loopback
inet addr: 127.0.0.1 Mask: 255.0.0.0
inet6 addr::: 1 / 128 Scope: Host
UP LOOPBACK RUNNING MTU: 16436 Metric: 1
RX packets: 101 errors: 0 dropped: 0 overruns: 0 frame: 0
TX packets: 101 errors: 0 dropped: 0 overruns: 0 carrier: 0
collisions: 0 txqueuelen: 0
RX bytes: 22221 (21.7 KiB) TX bytes: 22221 (21.7 KiB)
I use the iwconfig command, the result is:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11 ESSID: ""
Mode: Managed Frequency: 2.412 GHz Access Point: Not-Associated
Tx-Power = 0 dBm
Retry min limit: 7 RTS thr: off Fragment thr = 2352 B
Encryption key: off
Link Quality: 0 Signal level: 0 Noise level: 0
Rx invalid nwid: 0 Rx invalid crypt: 0 Rx invalid frag: 0
Tx excessive retries: 0 Invalid misc: 0 Missed beacon: 0
I began to configure:
iwconfig wlan0 essid "links"
iwconfig wlan0 key "*******"
Once again, I use the command ifconfig wlan0 up
System gave me a hint: Connection timed out
Each boot, the computer will prompt:
receive_packet failed on wlan0: network is down
failed to bring up wlan0
DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8.
send_packet: network is down
